Section XVI. DOORS, FRONT GRILLE AND TOP SCREEN AND BATTERY FRAME

TM 5-4110-217-14

Clean and Inspect.

(1) Clean starter with a clean lint-free cloth. 3-

(1) Clean power supply with clean lint-free

3-68.

Thermometer.

cloth or compressed air.

a. Removal (fig. 6-2).

(2) Inspect power supply for cracks, burning

(1) Carefully pull thermometer bulb through

other damage. Replace, if defective.

the condenser section.

c. Installation.

(2) Remove three screws (64), washers (65),

(1) Align mounting holes in power supply (36)

and nuts (66) that secure thermometer (61) to the

with holes in control box, and secure with screws (37),

refrigeration unit frame and remove thermometer.

and washers (38).

b. Cleaning and Inspection.

(2) Replace all wires as in original

(1) Clean thermometer with a clean lint-free

configuration.

cloth.

(3) Refer to paragraph 3-57c and replace

(2) Inspect thermometer for dents, cracks, or

control box assembly.

other damage.

Thermometer must be replaced if

defective

3-67.

Magnetic Starter (Model RMP-J/11-10E)

c. Installation.

Removal (fig. 8-3).

(1) Align holes in thermometer (61) with holes

(1) Disconnect power source to refrigeration

in refrigeration unit frame and secure with three screws

unit.

(64), washers (65) and nuts (66).

(2) Remove nuts (7) and washers (6) that

(2) Carefully thread thermometer bulb

secure starter (5).

through condenser to panel and grille in rear of

(3) Disconnect and tag wiring at starter.

evaporator section.

b. Cleaning and Inspection.

Section XVI. DOORS, FRONT GRILLE AND TOP SCREEN AND BATTERY FRAME

removal procedures above.

3-69.

General.

(2) Inspect for cracks, dents or other damage.

The doors, grille, screen and battery frame are

Replace defective parts if unrepairable.

covered in this section.

3-72.

Fuel Tank (fig. 3-24).

3-70.

Battery Frame (Model RMP-J/1-10G)

Removal.

Removal (fig. 3-24).

(1) Drain fuel tank (12) by removing drain

(1) Remove cables (5 and 6, fig. 3-20) from

plug (16).

battery).

(2) Remove panel (10) by removing four

(2) Remove two nuts (65) and stud (64)

screws (11).

securing battery frame.

(3) Disconnect fuel line hose (84) by

b. Cleaning and Inspection.

removing clamps (85).

(1) Clean battery frame, battery pan and

(4) Disconnect gas tank-to-pump line (87).

hardware with an approved cleaning solvent and dry

(5) Loosen fuel tank hold down clamps (13).

thoroughly.

(6) Push fuel tank slightly forward to clear

(2) Inspect for worn or damaged parts.

drain pipe. Lift tank out of unit.

Replace if required.

b. Cleaning and Inspection.

c. Installation. Reinstall per original configuration.

(1) Clean all parts with approved cleaning

solvent and dry thoroughly.

3-71.

Top Screen, Doors and Grille.

(2) Inspect tank for leaks or other damage.

Removal (fig. 3-24).

Replace defective parts.

(1) Remove top screen (1) by unscrewing

c. Installation.

screws (11).

(1) Place tank into unit as in original

(2) Remove doors and grille as shown in

configuration. Line up drain pipe with hole in unit.

figure 3-24.

(2) Tighten fuel tank hold down clamps (13).

b. Cleaning and Inspection.

(3) Connect gas tank-to-pump line (87).

(1) Clean top screen, doors and grille with an

(4) Connect fuel line hole (84) with clamps

approved cleaning solvent and dry thoroughly.

(85).

(2) Inspect for damage. Replace, if defective.

(5) Fill fuel tank with fuel.

c. Installation.

(6) Re-install panel (10).

(1) Using a serviceable starter, reverse

3-35