Click here to make tpub.com your Home Page

Page Title: Explanation of Columns in the MAC, Section II.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

TM 5-4110-240-13&P
2
3,
i. Repair. The application of maintenance services , including fault location/troubleshooting  removal/installation,
4
5
and disassembly/assembly procedures, and maintenance actions to identify troubles and restore serviceability to an item
by correcting specific damage, fault, malfunction, or failure in a part, subassembly, module (component or assembly), end
item, or system.
j. Overhaul.
That maintenance effort (service/action) prescribed to restore an item to a completely
serviceable/operational condition as required by maintenance standards in appropriate technical publications (i.e., DMWR).
Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul does not normally return an
item to like new condition.
k. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like new
condition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel maintenance
applied to Army equipment.  The rebuild operation includes the act of returning to zero those age measurements
(hours/miles, etc.) considered in classifying army equipment/components.
B-3.
Explanation of Columns in the MAC, Section II.
a. Column 1, Group Number. Column 1 lists functional group code numbers, the purpose of which is to identify
maintenance significant components, assemblies, subassemblies, and modules with the next higher assembly. End item
group numbers shall be "00".
b. Column 2, Component/Assembly. Column 2 contains the names of components, assemblies, subassemblies, and
modules for which maintenance is authorized.
c. Column 3, Maintenance Function. Column 3 lists the functions to be performed on the item listed in Column 2.
(For detailed explanation of these functions, see paragraph B-2).
d. Column 4, Maintenance Category. Column 4 specifies, by the listing of a work time figure in the appropriate
subcolumn(s), the category of maintenance authorized to perform the function listed in Column 3. This figure represents
the active time required to perform that maintenance function at the indicated category of maintenance. If the number or
complexity of the tasks within the listed a. maintenance function vary at different maintenance categories, appropriate
work time figures will be shown for each category. The work time figure represents the average time required to restore an
item (assembly, subassembly, component, module, end item, or system) to a serviceable condition under typical field
operating conditions.  This time includes preparation time (including any necessary disassembly/assembly time),
troubleshooting/fault location time, and quality assurance/quality control time in addition to the time required to perform the
specific tasks identified for the maintenance functions authorized in the maintenance allocation chart.  The symbol
designations for the various maintenance categories are as follows:
C ................................................................................................... Operator or Crew
O.................................................................................. Organizational Maintenance
F .................................................................................. Direct Support Maintenance
H ............................................................................... General Support Maintenance
L ................................................................................... Specialized Repair Activity6
D ................................................................................................ Depot Maintenance
2
Services - inspect, test, service, adjust, align, calibrate, and/or replace.
3
Fault locate/troubleshoot - The process of investigating and detecting the cause of equipment malfunctioning; the
act of isolating a fault within a system or unit under test (UUT).
4
Disassemble/Assemble - encompasses the step-by-step taking apart (or breakdown) of a spare/functional group
coded item to the level of its least componency identified as maintenance significant (i.e., assigned an SMR code) for the
category of maintenance under consideration.
5
Actions - welding, grinding, riveting, straightening, facing, remachinery, and/or resurfacing.
6
This maintenance category is not included in Section II, column 4 of the Maintenance Allocation Chart. To identify
functions to this category of maintenance, enter a work time figure in the "H"
B-2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business