5-25.    Receiver a.   Removal. discharge   the Refer   to   paragraph   6-3   a   nd refrigerant system. Refer   to paragraph  4-21  and  remove  rear  top  cover.  Remove four  screws  and  two  mounting  straps  (fig.  5-8). Disconnect   receiver   tubing. b.   Installation.   Install   receiver   and   colder connections.   Install   two   mounting   straps   a   nd   four screws   using   sealing   compound   on   screw   threads. Refer   to   paragraph   6-3   and   charge   the   refrigerant system. 5-26.   Liquid   Sight   Indicator a.   Removal.   Refer   to   paragraph   6-3   and discharge   the   refrigerant   system.   Remove   housing rear  top  cover  (para  4-21  ).  Remove  two  screws  and lock   washers   from   sides   of   liquid   sight   indicator (fig.   1-2   )   and   remove   mounting   bracket   (fig.   5-8) from   inside   housing.   Unsolder   liquid   sight   indicator from   tubing. b.   Installation.   Solder   liquid   sight   indicator   on tubing.   Place   bracket   over   indicator   on   inside   of housing   and   secure   with   two   screws   and   lock washers.  Install  housing  top  rear  cover  (para  4-21). Refer   to   paragraph   6-3   and   charge   the   refrigerant system. 5-27.   Solenoid   Valves a.   Removal.   Removal   procedures   for   the   bypass solenoid   valve   and   the   equalizer   solenoid   valve   are the   same   except   for   the   mounting   hardware. (1)   Refer   to   paragraph   6-3   and   discharge   the refrigerant   system. (2)   Refer   to   paragraph   4-21   and   remove housing   rear   top   cover. (3)   Disconnect   solenoid   valve      electrical connector. (4)  Remove  two  socket-head  cap  screws  from underside   of   valve   body   and   carefully   remove bonnet   assembly.   Do   not   drop   plunger.   Remove diaphragm. Caution:   Remove   bonnet   assembly   and diaphragm   before   applying   heat   to   valve   body. (5)   To   remove   liquid   bypass   solenoid   valve (fig.   5-8), unsolder bushings. remove   two valve   body screws from and   spacers   and tubing. Remove (6)   To   remove   equalizer   solenoid   valve, remove   two   screws   a   nd   lock^- washers   that   secure valve   body   to   bracket.   Unsolder   valve   body   and remove    bushings. b.   Installation.   Install   solenoid   valves   as   follows: (  1  )  Install  bushings  in  valve  body  and  solder body   on   tubing. (2)   When   installing   equalizer   solenoid   valve body,   secure   body   to   bracket   with   two   screws   and lock   washers   install   from   underside   of   bracket   into valve   body. (3)   When   installing   liquid   bypass   solenoid valve   body, install   spacers   between   body   and housing   and   install   two   screws   from   outside   of housing. (4)  Place  diaphragm  in  the  body  with  the  pilot port   extension   away   from   body.   Hold   plunger   with synthetic   seat   a   gainst   pilot   port.   Make   sure preformed   packings   are   in   place   and   lower   bonnet assembly   over   plunger.   Install   body   screws. (5)   Connect   electrical   connector. (6)   Refer   to   paragraph   4-21   and   install housing   rear   top   cover. (7)   Refer   to   paragraph   6-3   and   charge   the refrigerant   system. 5-28.   Thermal   Expansion   Valve a.  GeneraI.  The  main  thermal  expansion  valve  is hermetically   sealed   and   cannot   be   repaired. b.   Rermoval.   Remove   the   thermal   expansion valve   as   follows: (1)   Refer   to   paragraph   6-3   and   discharge   the refrigerant   system. (2)   Remove   housing   top   covers   (para   4-21). (3)   Soften   mastic   in   bulb   well   (fig.   5-9)   and remove   bulb   from   well.   Take   care   to   prevent dam   age   to   capillary   tube. (4)   Unsolder   thermal   expansion   valve   from tubing. 5-15