Special Information. - TM-5-4110-204-130074

TM 5-4110-204-13

the

d. Unit of issue indicates the unit used as a

identified with an asterisk in

basis of issue, e.g., ea, pr, ft, yd, etc.

allowance column.

(2) The quantitative allowances for DS level

e. Quantity incorporated in unit pack indicates

the actual quantity contained in the unit pack.

o f maintenance will represent initial

stockage for a 30-day period for the

f. Quantity incorporated in unit indicates the

number of equipments supported.

quantity of repair parts in an assembly. Where an

asterisk appears, refer to Table 4--2 and figures

i. I l l u s t r a t i o n .

41 and 4--2 for quantities applicable to a par-

( 1 ) Figure number indicates the figure

ticular model.

number of the illustration by which the

g . Fifteen-Day organizational maintenance

item is shown.

allowance.

(2) Item or symbol number indicates the

(1) The allowance columns are divided into

callout number used to reference the item

four subcolumns. Indicated in each sub-

in the illustration.

column is the quantity of items authoriz-

D-4. Special Information.

ed for the number of equipments sup-

ported. Items authorized for use as re-

quired but not for initial stockage are

Quantity shown in quantity incorporated in unit

i d e n t i f i e d w i t h a n a s t e r i s k i n the

reflects total for all units. Refer to figures 4--1 and

allowance column.

42 for quantity of specific unit.

(2) T h e q u a n t i t a t i v e a l l o w a n c e s f o r

D-5. How to Locate Repair Parts.

organizational l e v e l of maintenance

represents one initial prescribed load for

a. When National stock number is unknown.

a 15-day period, f o r t h e n u m b e r o f

equipments supported. U n i t s a n d

(1) F i r s t . U s i n g t h e i n d e x o f c o n t e n t s ,

organizations a u t h o r i z e d a d d i t i o n a l

determine the functional group or

prescribed loads will multiply the number

s u b g r o u p , i.e., engine, engine assembly,

of prescribed loads authorized by the

transmission, transmission assembly,

within which the repair part belongs. This

quantity of repair parts reflected in the

is necessary because separate illustra-

appropriate density column to obtain the

total quantity of repair parts authorized.

tions are prepared for functional groups

or subgroups, and listings are divided in-

(3) Subsequent changes to allowances will be

to functional groups.

limited as follows: No change in the range

(2) Second. Find the repair part illustration

of items is authorized. If additional items

in the back of the publication covering the

are considered necessary, recommenda-

functional group or subgroup to which the

tion should be forwarded to US Army

repair part belongs.

T r o o p Support and Aviation Materiel

(3) Third. Identify the repair part on the

Readiness Command for exception or

illustration figure and item number of the

revision to the allowance list. The range

repair part.

of items authorized will be made by this

Command based upon engineering ex-

(4) Fourth. Using the repair parts listing,

perience, demand data, or TAERS in-

find the functional group or subgroup of

formation.

the repair part and the illustration figure

and item number as noted on the illustra-

h. Thirty-Day DS Maintenance Allowance.

tion.

(1) The allowance columns are divided into

three subcolumns. Indicated in each sub-

b. When National stock number or manufac-

c o l u m n is the total quantity of items

turer's part number is known.

authorized for the number of equipments

(1) First. Use the index to locate the

supported. Items authorized for use as re-

National stock number or manufactur-

quired but not for initial stockage are

Change 10

D-2