|
| |
TM 5-4120-270-15
Paragraph
Page
Equipment-Continued
Inspection .....................................................................................................
2-3
2-1
Installation ....................................................................................................
2-5
2-1
Instruments...................................................................................................
2-9
2-3
Movement ...................................................................................................
2-6
2-2
Operation......................................................................................................
2-13
2-5
Servicing.......................................................................................................
2-3
2-1
Setting up .....................................................................................................
2-5
2-2
Special..........................................................................................................
3-1
3-1
Unloading .....................................................................................................
2-1
2-1
Unpacking ....................................................................................................
2-2
2-1
-
Evaporator:
Fan and inlet ring..........................................................................................
3-28
3-10
Heater thermostat.........................................................................................
5-20, 6-11
5-4, 6-8
Motor contactor ............................................................................................
6-5
6-1
Evaporator coil:
Removal .......................................................................................................
5-23, 6-23
5-4, 6-14
Service .........................................................................................................
3-10
3-4
Fan:
Condenser....................................................................................................
3-29
3-10
Evaporator....................................................................................................
3-28
3-10
Guard ...........................................................................................................
3-27
3-10
Fresh air inlet filter
Removal .......................................................................................................
3-26
3-10
Service .........................................................................................................
3-9
3-4
Fresh air inlet screen .........................................................................................
3-27
3-10
Fittings ...............................................................................................................
6-16
6-11
Fuse service ......................................................................................................
3-34
3-16
Grilles.................................................................................................................
3-25
3-10
Heater elements ................................................................................................
5-20, 6-10
5-4, 6-8
Heater thermostat ..............................................................................................
5-20, 6-11
5-4, 6-8
High discharge pressure....................................................................................
5-7, 6-14
5-2, 6-11
High pressure cutout switch...............................................................................
5-28,6-21
5-6, 6-14
High suction and low discharge pressures ........................................................
5-7, 6-14
5-2, 6-11
Hose ..................................................................................................................
5-35
5-8
Hose clamps ......................................................................................................
5-35
5-8
Hot gas bypass solenoid valve ..........................................................................
5-26, 6-18
5-6, 6-13
Identification and tabulated data........................................................................
1-4,4-4
1-1, 4-1
Inspecting and servicing the equipment ............................................................
2-3
2-1
Inspecting equipment ........................................................................................
2-3
2-1
Installation after movement................................................................................
2-7
2-2
Installation of separately packed components ...................................................
2-4
2-1
Installation or setting up instructions .................................................................
2-5
2-1
Instruments ........................................................................................................
2-9
2-3
Junction box.......................................................................................................
5-19
5-4
Leads, electrical.................................................................................................
3-35, 6-12
3-16, 6-9
Liquid line and liquid line bypass solenoid valve ...............................................
5-26, 6-19
5-6, 6-13
Little or no heating capacity...............................................................................
3-17, 5-10
3-7, 5-3
Low pressure cutout switch ...............................................................................
5-28,6-21
5-6, 6-14
Mist eliminator service .......................................................................................
3-10
3-4,
Model difference ................................................................................................
1-5
1-8
Motor, blower:
Removal .......................................................................................................
5-21
5-4
Testing..........................................................................................................
6-9
6-6
Movement to new worksite ................................................................................
2-6
2-2
Operation:
Air conditioner ..............................................................................................
2-13
2-5
In dusty or sandy areas ................................................................................
2-16
2-5
In extreme cold .............................................................................................
2-14
2-5
In extreme heat ............................................................................................
2-15
2-5
Under rainy or humid conditions ...................................................................
2-17
2-6
I-2
|
