Quantcast MOTOR ALTERNATING CURRENT (B2) (Continued) 4120-01-069-1321)">

 

Click here to make tpub.com your Home Page

Page Title: MOTOR ALTERNATING CURRENT (B2) (Continued)
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 4-66. Motor (B2) Welco Industries, Inc.
Up
TM-5-4120-359-14 Air Conditioner Split Package 18 000 BTU/HR Cooling 30 000 BTU/HR Heating 208 Volt 3 Phase 400 Hertz Manual
Next
FLEXIBLE HOSE ASSEMBLY SUCTION AND DISCHARGE - 506780226
TM 5-4120-359-14
(g) Carefully place the rotor and shaft with bearings back in the motor housing.
(h) Using screwdriver, secure the end caps to the motor with eight screws and washers. Before tightening
completely, spin shaft to see that it spins freely. If any rubbing is noted, adjust the end caps slightly to relieve rubbing.
Finish tightening the eight screws.
(i) Check end play of shaft. End play should be 0.002-0.005 inch (0.051-0.127 mm). If end play is not within
limits, disassemble motor and add or remove shims to adjust.
(3) To replace bearings on Welco Industries, Inc. motors:
(a) Using screwdriver, remove four screws and washers and carefully remove the end bracket.
(b) Carefully pull the rotor with shaft assembly from the motor housing.
(c) Note the position and number of washer bearing spacer(s), load spring, and bearings as they are
removed.
(d) Remove the washer bearing spacer(s) and load spring and pull the bearings from the shafts.
(e) Place the new bearings on the shafts.
(f) Place the load spring and washer bearing spacer(s) back on shaft in same position as removed.
(g) Carefully place the rotor with shaft with bearings back in the motor housing.
(h) Using screwdriver, secure the end bracket to the housing assembly with four screws and washers.
Before tightening completely, spin shaft to see that it spins freely. If any rubbing is noted, adjust the end cap slightly to
relieve rubbing. Finish tightening the four screws.
(i) Check end-play of shaft. End play should be 0.002-0.005 inch (0.051-0.127 mm). If end play is not within
limits, disassemble motor and add or remove shims to adjust.
e. Installation
(1) Slip the motor into place and position impeller and extension shaft loosely on motor shaft.
(2) Line up motor and bracket screw holes.
(3) Using socket and ratchet, fasten motor to bracket with four screws, lock washers, and flat washers.
(4) Aline extension shaft setscrews with flat surface on motor shaft.
(5) Position impeller for 1/8 inch clearance (measure with tape) from inside edge of fan inlet.
(6) Using allen wrench, tighten two setscrews to secure shaft extension and impeller on motor shaft.
(7) Spin impeller and check that it clears inlet all around.
(8) If impeller does not spin freely, increase clearance, step (4) slightly.
(9) Connect P11 connector plug to J11 motor connector.
Follow-on Procedures: 1. Install top condenser cover. (See paragraph 3-25.)
2. Connect power.
4-137

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.