 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 5-4110-217-14
(3) Remove nut and lockwasher securing
(2) Remove plug-in type starter relay (33)
fuseholder (23) to control panel and remove fuseholder.
from printed circuit board (29).
b. Cleaning and Inspection.
b. Cleaning and Inspection.
(1) Clean fuseholder with clean lint-free cloth.
(1) Clean relay with a clean lint-free cloth.
(2) Inspect for cracks, chips, or other
(2) Inspect relay for cracks, chips, or other
damage. Replace if defective.
damage. Replace if defective.
c. Installation.
c. Installation.
(1) Place fuseholder (23) in hole in control
(1) Plug-in starter relay (33) to printed circuit
panel and secure with nut and lockwasher.
board (29).
(2) Refer to paragraph 3-57c and replace
(2) Connect wires as in original configuration.
control box assembly.
(3) Refer to paragraph 3-57c and replace
control box assembly.
3-64.
Defrost Relay.
3-61.
On-Off Switch.
a. Removal (fig. 3-23).
a. Removal fig. 3-23).
(1) Refer to paragraph 3-57a and remove
(1) Refer to paragraph 3-57a and remove
control box assembly.
control box assembly.
(2) Remove plug-in type defrost relay (34)
(2) Remove retaining nut that secures switch
from printed circuit board (29).
(21) to panel at front of panel.
b. Cleaning and Inspection.
(3) Remove wires at rear of switch, carefully
(1) Clean and defrost relay with a clean lint-
labeling each wire for correct terminal.
free cloth or compressed air.
b. Cleaning and Inspection.
(2) Inspect relay for cracks, chips, burned or
(1) Clean switch with a clean lint-free cloth.
pitted points, or other damage. Replace, if defective.
(2) Inspect for cracks, chips, or other
c. Installation
damage. Replace if defective.
(1) Plug-in defrost relay (34) to printed circuit
(3) Refer to paragraph 3-57c and replace
board (29).
control box assembly.
panel box assembly.
3-62.
Crank Limit Relay.(Model RMP- J/1-10G
3-65.
Defrost Timer
only)
a. Removal (fig. 3-23).
a. Removal (fig. 3-23).
(1) Refer to paragraph 3-57a and remove
(1) Refer to paragraph 3-57a and remove
control box assembly.
control box assembly.
(2) Remove plug-in type crank limit relay (35)
(2) Remove two screws (9), washer(10) and
from printed circuit board (29).
nuts (11) attaching defrost timer (8) to control box front
b. Cleaning and Inspection.
panel.
(3) Disconnect all wires, carefully labeling
(1) Clean relay with a clean lint-free cloth.
each for proper terminal.
(2) Inspect relay for cracks, chips, or other
b. Cleaning and Inspection.
damage. Replace if defective.
c. Installation.
(1) Clean timer with a clean lint-free cloth.
(2) Inspect timer for cracks, chips, dents or
other damage. Replace, if defective.
CAUTION
c. Installation.
When reassembling relays (33, 34, 35,
(1) Connect all wires as in original
configuration.
forcefully.
Printed circuit card may
(2) Align holes in defrost timer (8) with holes
crack.
on control box front panel and secure with two screws
(9), washers (10) and nuts (11).
(1) Plug-in relay (35) to printed circuit board
(3) Refer to paragraph 3-57c and replace
(34).
control box assembly.
(2) Refer to paragraph 3-57c and replace
control box assembly.
3-66.Power Supply (Model RMP-J/11-0E)
a. Removal (fig. 3-23).
3-63.
Starter Relay
(1) Refer to paragraph 3-57a and remove
a.
Removal (fig. 3-23).
control box assembly.
(1) Refer to paragraph 3-57a and remove
(2) Disconnect all wires at power supply (36)
control box assembly.
terminals, carefully label each for proper terminal.
(3) Remove four screws (37) and washers
(38) securing power supply to control box.
3-34
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals