 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 5-4110-217-14
1.
Cover
15.
Nut, hex
27.
Washer, lock
2.
Gasket
16.
Ammeter (RMP-J/1-loG Only)
28.
Nut, hex
3.
Screw
17.
Lens, red
29.
Printed Circuit Board Assembly
4
Washer, lock
18.
Lens, amber
30.
Screw
5.
Thermostat
19.
Socket, lamp
31.
Washer, lock
6.
Screw
20.
Lamp
32
Screw
7.
Washer, lock
21.
Switch, on-off
33.
Relay, temp & refrigeration (K-1)
over-pressure
8.
Timer, defrost
22.
Switch, pushbutton, defrost
34. Relay, defrost (K-3)
9.
Screw
23.
35. Relay, starter (K-2) (RMP-J/1-1OG Only)
10.
Washer, lock
24.
Fuse, 10 amp (RMP-J/1-10OG) 36. Power Supply (RMP-J/11-IOE Only)
11.
Nut, hex5 amp (RMP-J/11-10E)
37.
Screw
12.
Hourmeter
25.
Connector, receptacle
38. Washer
13
Screw
26.
Screw
39. Control box
14.
Washer, lock
Figure 3-23 - Continued.
b. Carefully pull control box from the unit and
b.
Clean and Inspect.
(1) Clean ammeter with clean lint-free cloth.
disconnect cable from connector (25, fig. 3-23).
c. Remove seven screws and washers (3 and 4,
(2) Inspect ammeter for dents, cracks, or
other damage. If ammeter is defective, it must be
replaced.
components for possible replacement.
c. Installation.
(1) Replace nuts that secure ammeter (16) to
3-57.
Hourmeter.
panel.
a.
Removal (fig. 3-24).
(2) Connect all wires as in original
(1) Loosen the six screws fastening the
configuration.
control box assembly (6, fig. 3-24) to the refrigeration
(3) Replace control box per paragraph 3-57c.
unit frame, and carefully pull out the control box. Try not
to disturb the wiring.
3-59.
Thermostat.
(2) Remove No. 11 wire (positive) and No.
a.
Removal (fig. 3-23).
wire (negative) from back of hourmeter (12).
(1) Refer to paragraph 3-57a and remove
(3) Remove three screws (13), washers (14)
control box assembly.
and nuts (15) securing hourmeter to control box front
(2) Disconnect all wires and carefully label
panel.
each for proper terminal.
b. Clean and Inspect.
(3) Remove four screws (6) and washers (7)
(1) Clean hourmeter with a clean lint-free
that secure thermostat (5) to panel.
cloth.
b. Cleaning and Inspection.
(2) Inspect hourmeter for dents, cracks, or
(1) Clean thermostat with a clean lint-free
other damage. If hourmeter is defective, it must be
cloth or compressed air.
replaced.
(2) Inspect thermostat for cracks, chips, or
c. Installation.
other damage. Replace thermostat if defective.
(1) Align holes in hourmeter (12) with holes in
c. Installation.
panel and secure with three screws (13), washers (14)
(1) Align mounting holes in thermostat(5) with
and nuts (15).
hole in panel and secure with four screws (6) and
(2) Connect No. 11 wire on positive terminal
washers (7).
and No. 8 wire on negative terminal at back of
(2) Replace all wires as in original
hourmeter.
configuration.
(3) Install control box assembly into
(3) Replace control box assembly per
refrigeration unit and fasten with six screws.
3-58.
Ammeter. (Model RMP-J/1-10G)
3-60.
a.
Removal (fig. 3-24).
a.
Removal (fig. 3-23).
(1) Refer to paragraph 3-57a and remove
(1) Refer to paragraph 3-57a and remove
control box assembly.
control box assembly.
(2) Disconnect all wires at ammeter (16)
(2) Disconnect wires and carefully label each
terminals; carefully label each terminal.
for proper terminal.
(3) Remove two nuts securing ammeter (16)
to front panel bracket.
3-33
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals