 |
|||
|
|
|||
|
Page Title:
Table 3-1. Operator Preventive Maintenance Checks and Services |
|
||
| ||||||||||
|
|
 TM 5-4110-217-14
Table 3-1. Operator Preventive Maintenance Checks and
Services
and Services - Continued
B-Before Operation D-During Operation A-After Operation
Time required: 1.1
Time required: 0 3
B-Before Operation
D-During Operation
A-After Operation
Time required 1.1
Time required 0.3
Interval
Item to be inspected procedure
Work
Corrective
Interval
Item to be inspected procedure
Work
and
time
action
Corrective
sequence no
(M/H)
para
and
time
action
BDA
ref
sequence no
(M/H)
para
NOTE
BDA
ref
Visually inspect for evidence
of lubricant and fuel leaks
9
OPERATION
NOISE
OR
concur-rently with the daily
VIBRATIOI
service checks. Lubricate in
During operation observe for
accor-dance
with
current
any unusual noise or vibration
0.1
3-15
lubrication order
(Daily)
NOTE
10
REFRIGERATION SYSTEM
Use distilled water or a good
Visually check all connections
grade drinking water (exclud-
of the refrigeration system for
0.2
ing mineral water)
leaks. Check liquid line sight
1
BATTERY (Model RMP-J/1-
glass for air bubbles or milky
10G) Tighten loose cables
appearance
Report
and mountings.
Remove
deficiencies to Direct Support
corrosion.
0.1
3-48
Unit for correction (Daily)
Inspect for cracks and leaks
Fill to 3/8 inch above plates.
3-8.
Organizational Preventive
Maintenance
Clean vent holes m filler caps
Checks and Services.
before installing In freezing
a.
This paragraph contains a tabulated listing of preventive
weather,
run
engine
a
maintenance checks and services which must be performed by
minimum of 1 hour after
organizational maintenance personnel at quarterly intervals A quarterly
adding water. (Weekly)
interval is equal to 3 calendar months, or 250 hours of operation,
2
ALTERNATOR BELT
whichever occurs first.
Inspect fan belt for proper
b.
The item numbers are listed consecutively and indicate
tension (Weekly)
0.1
3-12
the sequence of minimum requirements Refer to table 3-2 for quarterly
3
AIR CLEANER (Model RMP-
Preventive Maintenance Services
J/1-10G)
Clean as required This
Table 3-2. Organizational Preventive Maintenance Checks and
service
0.2
3-5f
Services
will vary from a few days of
Q-Quarterly
operation in comparatively
Total man-hours required:
clean conditions to twice a
Sequence
Item to be inspected procedure
Work
day in dusty conditions.
Corrective
4
ENGINE OIL LEVEL
number
time
action
(Model RMP-J/1-10G)
(M/H)
para
Add oil as indicated by the
ref
engine oil level indicator (dip-
0.2
3-5
NOTE
stick).
Refer to current
lubrication order (Daily)
Visually inspect for evidence
5
DRIVE
of lubricant and fuel leaks
BELTS
con-currently with the daily
AND ALTERNATOR BELT
service checks. Lubricate in
Check belts for proper tension
0.1
3-13
accordance
with
current
(Weekly)
lubrication order
6
SIGHT
NOTE
GLASS
Use distilled water or a good
NOTE
grade
drinking
water
When checking compressor
(excluding mineral water).
sight glass oil level, check
1
BATTERY (Model RMP-J/1-
prior to start up. When unit is
10G)
operating, be sure unit has
Tighten loose cables and
operated onlh enough to
mountings.
Remove
stabilize pressures, usually
corrosion.
0.2
3-48
15-20 minutes
Fill to 3/8 inch above the
Oil level should be halfway up
0.1
plates Clean vent holes in
sight glass Refer to Direct
filler caps before installation.
Support Unit for adding oil.
In freezing weather run
(Daily)
engine minimum of 1 hour
7
GOVERNOR LINKAGE
after adding water Replace a
(Model RMP-J/1-IOG)
cracked or leaking battery
Inspect and clean governor
01
3-30
2
ALTERNATOR BELT
linkage (Daily)
Adjust belt to proper tension
0.5
3-12
8
FUEL TANK (Model RMP-J/1-
Replace a worn, frayed or
10G)
cracked belt.
Add fuel as required (Daily)
0.2
Change 4 3-5
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals