Cleaning and Inspection - TM-5-4110-217-140045

TM 5-4110-217-14

1. "V" Belt

12.

Washer. RMPJ/10G

2. Rod assembly

13.

Sheave, Engine (Model RMP-J/1-10G)

3. Nut hex

14.

Engine, gasoline (Model RMP-J/1-10G)

4. Nut hex, jam

15.

"V Belt (Model RMP-J/11-1OE)

4A. Spacer

16.

Motor. electric (Model RMP-J/11-10E)

5. Washer, flat, nylon

17.

Screw (Model RMP-J/11-10E)

6. Engine/Motor Adjustment Plate

18.

Washer, lock (Model RMP-J/11-10E)

7. Bolt

19.

Plate assembly, motor adapter (Model RMP-

8. Washer, lock

J/11-1OE)

9. Plate, mounting

20. Screw (Model RMP-J/11-10E)

10. Compressor

21. Washer, lock (Model RMP-J/11-10E)

11 Screw

22. Bushing (Model RMP-J/11-10E)

Figure 3-9. - Continued.

(3) Remove all electrical wires to engine

(3) Replace compressor drive V-belts on to

carefully labeling each for proper terminal. Remove

sheave and adjust belts. Refer to paragraph 3-11.

toggle switch and its attaching parts (16, 18, 19, 20, 21,

(4) Install air cleaner (1, fig. 3-11). Tighten

fig. 3-11) from engine).

screw (3, fig. 3-11).

(4) Remove alternator (40, fig. 3-11) from

(5) Connect flexible tubing (94, fig. 3-24) to

engine and disconnect wiring to alternator and control

muffler (95, fig. 3-24). Tighten two clamps (93, fig. 3-

panel. Replace alternator on to engine and secure per

24)

original mounting with two nuts (47, fig. 3-11).

(6) Remove alternator (40, fig. 3-11) from

(5) Disconnect flexible tubing (94, fig. 3-24)

engine and connect wiring to alternator and control

to muffler (95, fig. 3-24) by loosening two clamps (93,

panel. Replace alternator on to engine and secure per

fig. 3-24).

original mounting with two nuts (47, fig. 3-11).

(6) Remove air cleaner (1, fig. 3-11) by

(7) Install toggle switch with its attaching parts

loosening screw (3, fig. 3-11).

(16, 18, 19, 20 and 21, fig 3-11) to engine. Connect all

(7) Refer to paragraph 3-13 and loosen and

electrical wires to engine.

remove compressor drive V-belts from sheave.

(8) Assemble air cylinder housing (11, fig. 3-

(8) Close the fuel shutoff valve on fuel filter

11) to engine with two screws (12, fig. 3-11).

(10, fig 3-10). Disconnect fuel pump line (3, fig. 3-10)

(9) Connect negative battery cable (5, fig. 3-

from engine.

20) to battery terminal. Install battery cover (7D, fig. 3-

(9) Remove four bolts and washers (7 and 8,

24) with four screws (5, fig. 3-24).

fig 3-9) securing engine (14, fig. 3-9) to mounting plate

3-22.

Electric Motor. (Model RMP-J/11-10E)

(9, fig. 3-9). Lift engine out through side of unit.

a. Removal.

b. Cleaning and Inspection.

(1) Move the control switch to OFF position.

(1) Clean engine with an approved cleaning

Disconnect the electric power at source.

solvent and dry thoroughly.

(2) Remove the motor junction box cover and

(2) Inspect engine for any external damage.

disconnect and tag the motor wire leads.

Replace or repair defective parts

(3) Refer to paragraph 3-13 and loosen and

c. Installation.

remove compressor drive V-belts

(1) Reinstall engine in unit through side of

(4) Remove the screws and lockwashers(17,

unit. Secure engine (14, fig. 3-9) to mounting plate (9,

18, fig. 3-9) securing motor to mounting plate. Lift motor

fig. 3-9) with four bolts and washers (7 and 8, fig. 3-9).

out of unit.

(2) Connect fuel pump line (3, fig. 3-10) to

b. Installation.

Using a serviceable motor,

engine at fuel filter fitting (57, fig. 3-11). Open fuel shut-

reverse removal procedure above. Adjust the belt

off valve on fuel filter (10,fig. 3-10).

tension on compressor drive and belts.

Change 3 3-13